Join Our Team
Aviosense is a deep-tech aerospace startup developing intelligent airborne remote sensing systems for autonomous and remotely piloted aircraft. Our mission is to empower next-generation airborne platforms with advanced sensing capabilities — enabling safer skies, smarter missions, and a new era of airborne intelligence.
Key Responsibilities
- Develop and maintain device drivers for hardware interfaces (SPI, I2C, UART, CAN, Ethernet)
- Implement real-time task scheduling and data pipeline architectures
- Design fault-tolerant software for mission-critical airborne systems
- Configure and optimize DMA controllers and interrupt handling
- Debug firmware using JTAG/SWD tools and logic analyzers
- Support prototype board bring-up and hardware-software integration
- Collaborate with hardware and RF engineers on system integration
- Participate in flight test campaigns and field testing
Required Qualifications
- BSc/MSc in Computer Engineering, Electrical Engineering, or related field
- 3+ years of experience in real-time embedded software development
- Strong proficiency in C/C++ for resource-constrained systems
- Experience with hardware interfaces: SPI, I2C, UART, CAN, Ethernet
- Hands-on experience writing device drivers and board support packages
- Familiarity with DMA controllers and interrupt-driven architectures
- Proficient with JTAG/SWD debugging tools
- Ability to read and interpret electrical schematics and datasheets
Nice to Have
- Experience with SoC-based embedded systems (e.g., Xilinx Zynq, TI Sitara)
- Familiarity with embedded Linux environments
- Exposure to aerospace or defense development constraints
- Knowledge of real-time signal processing pipelines
Key Responsibilities
- Design RF front-end circuits including TX/RX chains, LNAs, power amplifiers, and filters
- Perform RF system-level analysis: noise figure, gain budgets, linearity
- Conduct EM simulations and RF layout design for microwave PCBs
- Select and evaluate RF components for performance and reliability
- Build and validate RF prototypes using VNA, spectrum analyzers, and signal generators
- Support EMI/EMC compliance testing and mitigation strategies
- Collaborate with antenna, hardware, and embedded teams on system integration
- Participate in flight test campaigns and field validation
Required Qualifications
- MSc in RF Engineering, Microwave Engineering, or related field
- 3+ years of hands-on RF circuit design experience
- Proficiency in microwave PCB design and RF layout techniques
- Strong understanding of noise figure, gain budgeting, and impedance matching
- Experience with RF filtering, matching networks, and amplifier design
- Hands-on experience with VNA, spectrum analyzers, and signal generators
- Familiarity with EM simulation tools (e.g., ADS, HFSS, CST)
Nice to Have
- Experience with radar or phased-array systems
- Knowledge of mm-wave frequency design
- Exposure to aerospace or defense RF constraints
- Experience with anechoic chamber measurements
Key Responsibilities
- Create schematic designs for mixed-signal and digital circuits
- Perform electrical simulations for signal and power integrity
- Design high-speed PCBs with ADC/DAC, FPGA/SoC, and power supply subsystems
- Support prototype board bring-up, debug, and validation
- Collaborate with RF, embedded software, and mechanical teams
- Contribute to design reviews and documentation
- Support EMI/EMC testing and environmental qualification
Required Qualifications
- MSc or BSc in Electronics, Electrical Engineering, or related field
- 3+ years of experience in hardware design (mixed-signal and digital)
- Proficiency in high-speed mixed-signal PCB design
- Experience with FPGA/SoC-based system design
- Strong understanding of signal and power integrity analysis
- Proficiency with Altium Designer or equivalent EDA tools
- Familiarity with EMI/EMC fundamentals and design for compliance
Nice to Have
- Experience with radar, RF, or aerospace/defense electronics
- Knowledge of DO-254 or similar hardware certification standards
- Experience with environmental qualification testing
Key Responsibilities
- Customize and maintain embedded Linux distributions for ARM-based SoCs
- Develop and debug Linux kernel drivers for custom hardware interfaces
- Implement communication protocol stacks (Ethernet, PCIe)
- Build real-time data and signal processing pipelines in userspace
- Configure bootloaders, device trees, and system initialization
- Optimize system performance for throughput and latency-critical applications
- Collaborate with hardware and embedded teams on platform integration
- Support flight testing and field deployments
Required Qualifications
- BSc/MSc in Computer Engineering, Electrical Engineering, or related field
- 3+ years developing C/C++ software for embedded Linux systems
- Experience writing Linux kernel drivers and board support packages
- Proficiency with bootloaders and device tree configuration
- Strong understanding of ARM-based SoC architectures
- Debugging experience with JTAG/SWD, GDB, and kernel tracing tools
- Ability to read and interpret electrical schematics
Nice to Have
- Experience with Yocto Project or Buildroot
- Proficiency with Python or shell scripting for build automation
- Knowledge of secure boot and OTA update mechanisms
- Familiarity with real-time signal processing pipelines
Key Responsibilities
- Design antenna elements and array configurations for airborne applications
- Develop phased-array antenna structures with beam steering capabilities
- Optimize antenna performance through EM simulation and parametric analysis
- Select RF materials and manufacturing processes for antenna fabrication
- Validate antenna designs through anechoic chamber and open-range measurements
- Collaborate with RF, hardware, and mechanical teams on system integration
- Support flight test campaigns with antenna performance characterization
Required Qualifications
- MSc in Telecommunications, Electrical Engineering, or related field
- 3+ years of experience in phased-array antenna design
- Proficiency with EM simulation tools (e.g., HFSS, CST, FEKO)
- Strong understanding of antenna measurement techniques
- Hands-on experience with VNA, spectrum analyzers, and signal generators
- Knowledge of phased-array beam steering and calibration techniques
Nice to Have
- Experience with radar system design
- Knowledge of mm-wave frequency antenna design
- Exposure to aerospace or defense antenna constraints
- Experience with microwave PCB layout for antenna feeds
What We Offer
Build mission-critical systems
Work on airborne radar and sensing systems that directly impact flight safety and mission success.
Deep-tech aerospace R&D
Tackle cutting-edge challenges in RF engineering, signal processing, and embedded systems.
In-flight testing
See your work fly — participate in real platform integration and flight test campaigns.
Competitive compensation
Competitive salary package with equity potential in a growing aerospace startup.
Don't see a perfect fit? Send us your CV anyway.
info@aviosense.tech